How To Change Serpentine Belt on a Porsche Boxster (2009-2012)

Maintenance Interval 6 Years or 60,000 Miles (90,000 Kilometers)
Estimated Dealer Cost $450
Estimated Independent Mechanic Cost $300
Estimated DIY Cost $40
Repair Time 2.0 hours
DIY Difficulty Medium

Your engine uses a serpentine belt to power the accessories like the power steering and water pumps. Over time, the belt gets worn out and can slip or even break. Visually inspect your serpentine belt for cracks, fraying, and other damage. In any case, it is a good idea to replace your serpentine belt according to the manufacturer’s recommended service interval.

For an overview of the general procedure, check out the video above from YouTube channel, Gordan Rudman. While the video covers the process on a 987.1, but the process is very similar for the 987.2. You can find detailed parts, tools, and instructions below.

Find a Recommended Mechanic
Step-by-Step Instructions:

Step 1: Prepare your car and work area

  • Ensure engine is cold, so you don’t burn yourself.
  • Put on eye protection and gloves.
  • Gather parts and tools.

Step 2: Put the convertible top in service mode

  • While the video from Road and Race covers a 986, the process for putting the top in service mode is the same in the 987.
  • Start by releasing the convertible top via the latch.
  • Open the roof and stop when the top is opened ~8 inches.
  • Just under the compartment that covers the convertible top when it is down, disconnect the two cords located on each side of the top by simply pulling them out.
  • Unclip the base of the top from the hooks on each side.
  • Fold up the base of the top upward to reveal the horizontal carpet panel covering the engine.
  • There should be a strap that you can use to keep the base on the top in place.
  • Twist off the plastic clips that hold in the speaker and move the speaker back.

Step 3: Gain access to the engine

  • As shown in the video from Help Me DIY, slide and tilt both seats as far forward as possible to give yourself room to work. Note: The video is also for a 986, but is representative of the process on a 987.
  • You will see a vertical carpeted panel with another horizontally oriented carpeted panel just above.
  • With the speaker pushed back, lift up the edge of the horizontal carpet panel and remove the 4 plastic tabs by rotating them counter-clockwise.
  • Now you can pry the vertical carpet panel out to reveal the metal engine lid.
  • Use a ratchet and 10mm socket to remove the fasteners that hold the metal engine lid in place.
  • Remove the engine lid from the car.

Step 4: Remove the old serpentine belt

  • Before you replace the serpentine belt, take a picture of the belt routing pattern.
  • Locate the serpentine belt tensioner and use a shallow 30mm wrench to rotate it clockwise as far as it can go. This will remove tension from the belt.
  • While holding the tensioner in this position, use your other hand to remove the belt off the alternator pulley.
  • Slowly allow the tensioner to return to its original position, then guide the old belt off the remaining pulleys.
  • Remove the belt, then inspect each of the pulleys for excess play, binding, etc. If you detect any issues, it is a good idea to replace the defect pulleys.
Remove the old serpentine belt

Step 5: Install the new serpentine belt

  • Guide in the new belt and install it in reverse order.
  • Start with the coolant pump pulley and route the belt through the rest of the pulleys as shown in the diagram; put the belt over the tensioner pulley last.
  • Use the 30mm wrench to rotate the tensioner pulley clockwise.
  • Slide the belt over the tensioner pulley, then slowly allow the tensioner to return to its original position.

Step 6: Reinstall everything in reverse

  • Reinstall the engine lid and just snuggly hand tighten the fasteners.
  • Refit the vertical carpet panel and compartment cover.
  • Clean up your work area and put away your tools.

Add a Comment

Your email address will not be published. Required fields are marked *