How To Change Spark Plugs on a Porsche Boxster & Cayman (2009-2012)

Maintenance Interval 6 Years or 40,000 Miles (60,000 Kilometers)
Estimated Dealer Cost $500
Estimated Independent Mechanic Cost $300
Estimated DIY Cost $40
Repair Time 2 hours
DIY Difficulty Medium

Despite being relatively simple, spark plugs play a significant role in any gasoline engine. Their function is to produce a spark at the required time that ignites the air and fuel mixture. All spark plugs, being exposed to extreme pressures and temperatures that occur during engine operation, wear out with time. This can cause poor engine performance, misfire and drop in fuel economy. Also, a worn spark plug can have a larger electrode gap, which requires higher voltage and can lead to premature ignition coil failure.

While changing the spark plugs on your Porsche Boxster or Cayman, it is actually quite easy once you remove the rear wheels. And you can save quite a lot of money doing it yourself. To get an overview of the procedure, check out this video from the YouTube channel, D Wray’s Garage. Detailed step-by-step instructions, along with the parts and tools you’ll need, can be found below.

Find a Recommended Mechanic
Torque Specs & Fluid Capacities:

Spark plug: 22 ft-lbs
Ignition coil screws: 8 ft-lbs
Heat shield screws: 8 ft-lbs
Wheel bolts: 118 ft-lbs

Step-by-Step Instructions:

Step 1: Prepare your vehicle and work area

  • Ensure that your engine is cool so you don’t burn yourself and your car is parked on a flat surface.
  • Gather your parts and tools and wear gloves and safety glasses.

Step 2: Raise the rear of the vehicle off the ground

  • To give yourself enough clearance to work, safely raise your vehicle using a lift or jack and jack stands; ensure your car is level.
  • If using jack stands, you just need to raise the rear of the vehicle as shown in this video from SummitLife.
  • NEVER rely on a jack to keep your car up; use jack stands to safely support your vehicle.
  • Also be sure to use wheel chocks to prevent your car from rolling.
  • Once your car is on jack stands, give your car a hard shove to make sure it is secure.

Step 3: Remove the rear wheels

  • Use a 19 mm lug nut socket and breaker bar to loosen the wheel bolts.
  • To prevent damaging your wheels during removal and reinstallation, you can use wheel guide bolts to help slide the wheels off and help you remove your rear wheels without damaging your wheels.
  • As an added safety precaution, place a wheel under your vehicle under the engine block.

Step 4: Gain access to the igniton coils

  • Start by removing the small plastic piece covering the ignition coils; it is held on by T25 torx screws and 10mm nuts.
  • Remove the rear fender liner, which is also held on by T25 torx screws and a 10mm nut.
  • Now you should see a heat shield covering the ignition coils; remove the two E10 screws and move the heat shield out of the way.
  • Locate the ignition coils and remove the wiring connectors by pressing down on the plastic tab and pulling the connector off.
  • Remove the T30 torx screws on each ignition coil and pull out the ignition coils.
  • Inspect the ignition coils; if any are cracked, all of your ignition coils should be replaced.

Step 5: Replace the spark plugs

  • IMPORTANT: Never remove or install spark plugs on a hot engine or you can damage the spark plug threads.
  • Combine a spark plug socket with suitable extensions and a universal joint to remove the old spark plugs. 
  • To learn about how your engine is running, you can visually inspect each spark plug for contaminants and deposits as shown in this video from Dennis Kirk, Inc.
  • Insert the new spark plug into your spark plug socket and remove the cardboard covering the electrode tip; do not touch the tip.
  • Insert the new spark plug into the spark plug tube and hand tighten to prevent cross threading. Once the plug is threaded in all the way by hand, torque it to 22 ft-lbs.

Step 6: Reinstall the ignition coils

  • Insert the ignition coils and tighten the screws to 8 ft-lbs or just snuggly by hand.
  • Reconnect the wiring connectors.
  • Reinstall the heat shield and tighten the screws to 8 ft-lbs or just snuggly by hand.

Step 7: Repeat the prior steps on the other side of the engine

Step 8: Reinstall everything and lower the vehicle back onto the ground.

  • Reinstall the wheel liners.
  • Reinstall your wheels; be sure to tighten your wheels in a star pattern and torque your wheel bolts to 118 ft-lbs.
  • Lower your vehicle off the jack stands and remove the wheel chocks.
  • Clean up your work area and you’re all done!

One comment on “How To Change Spark Plugs on a Porsche Boxster & Cayman (2009-2012)

  1. Instead of pushing the upper half of the heatshield up where it keeps dropping down in the way, lift it and drop it between the lower shield and the exhaust box. It will only go part way down. Slide to the side to where it is clear of all the coils. It will stay there out of the way until you are ready to refit. Also note that on the opposite side there is a third fixing screw in from the back of the heat shield.

Add a Comment

Your email address will not be published. Required fields are marked *